Routine maintenance of IKO bearings begins with installation

When the bearing is replaced with a new one, the effect is different, and the same bearing as the original model must be used, and the effect in this aspect has a better meaning, so that it can be reflected in this aspect. Better results. First, the installation of IKO bearings will be introduced from the following cases.

When replacing a new bearing with a vibrating motor, the same bearing as the original model must be used.

1) Wash the bearing with kerosene, press it into the bearing seat, fill the roller of the outer ring of the bearing with Shell No. 3 lithium base grease to two-thirds full, apply evenly with the net hand, install the bearing gland, and apply the bolt The fastening bolt of the anti-loosening rubber presses the bearing gland;

2) The bearing is a cylindrical roller bearing with a detachable inner casing. The bearing should be placed on the rotating shaft and placed in place;

3) Mount the bearing housing on the casing. If there is grease grease hole, it must be aligned. Pressing the bearing block with the fastening bolts of the anti-loosening rubber;

4) The inner and outer eccentric blocks are mounted on the rotating shaft and are in place. If there is an axis key, the shaft key should be inserted into the keyway and then the outer eccentric block should be installed, and the shaft can be mounted on the rotating shaft with the retaining ring;

5) Tightly fix the eccentric block fastening bolts and turn the adjustable eccentric block to the angular position before the unloading and tighten the fastening bolts. After the above assembly is completed, the shaft should have a certain axial movement;

6) The protective cover on both ends of the upper vibration motor is fastened with screws.

IKO bearings have certain changes in the installation form of the vibration motor and other aspects of the performance, and the form considered from different angles has a certain change effect, and slowly the installation situation of all aspects has also been I understand it.

For more information and purchase please visit: https://www.supplyforever.com

IKO bearing heating fault repair method

The bearing is a fixed part of the machine and is the main body of the machine. Its function is basically to maintain the center position of the shaft and the mechanism for controlling the movement. IKO bearings play a decisive role in any machine. Without bearings, the machine will not work.

Many users have reported that when using IKO bearings, bearing heat failure is the most common, and this failure will also affect bearing life and performance. So how is this failure formed? Below, is the knowledge that is summarized for everyone.

1. The oil level is too low and the lubricant is lost from the oil seal;

2. The grease in the bearing housing is completely filled or the oil level is too high. This can lead to excessive lubrication, high temperature or oil leakage;

3. The contact type (friction) oil seal is too dry or the spring is too tight;

4. The inner hole of the bearing box is not round; the bearing box is twisted and deformed; the supporting surface is not flat; the inner diameter of the box hole is too small;

5. The contact type (friction) oil seal is too dry or the spring is too tight.

The smoothing agent inside the IKO bearing can be roughly divided into oil and grease.

Repair method: preparation: dry towel, sharp tongs, bearing cleaning night, smooth bearing oil or smooth grease.

1. Bearing cleaning fluid: Immerse the bearing in the bearing cleaning fluid bought on the market, and swing it. The foreign objects inside the bearing will be swayed in. Some supermarkets buy ultrasonic cleaning machines to sponsor foreign objects. .

2. Detection: For the IKO bearing that has been assembled into the original condition, grasp the inner ring with your fingers and turn it a few times.

3. Remove the C-shaped ring and the cover: wipe off the dirty color inside the bearing with a dry towel, then use the pointed pliers to lift the side of the C-shaped ring and take the C-shaped ring and the cover.

4. Inject the smoothing agent to inject grease or oil into the bearing according to the trend, and cover the cover with a new C-shaped ring.

5, boring: Take the IKO bearing from the cleaning solution, and wipe the cleaning solution with a dry towel, then dry it in a cool place.

For more information and purchase please visit: https://www.supplyforever.com